![]() ![]() When installing your last row of shingles, we are basing this on the assumption that you’ve already installed your drip edge. You will apply the cement to the parts of the shingles that are exposed. Trim the edges on the rake and top edge so that they are flush with the other shingles.Īpply the same roofing cement to the edges of the shingles along the top edge. Use bitumen-based roofing cement to cover each nail head. Nail the shingle with four nails – two in the adhesive stirp and two at either corner. When you get to the other edge, you will have one shingle strip with exposed nails. Remember, you are laying these in a perpendicular fashion so that the adhesive strip points towards the top edge of the shed. Nail each shingle strip so that it overlaps the nails of the previous shingle. ![]() An overhang of about 1 ½” beyond the top edge is ideal. Lay your first shingle strip so that it is flush to the rake end and covers any exposed nails of the shingles below. Each strip should be wide enough that, when placed perpendicular along the top edge of your shed roof, it covers the nails of the previous course of shingles. If the adhesive strip of the shingles is beyond the top edge, then avoid laying another row.Ĭut your shingles into strips. You’ll use your utility knife to trim the edge so that it is flush with the top edge of the roof. Your last course of shingles should come as close to the top as possible. This method will ensure your shed is completely weatherproof. Instead, you are going to cut your three-tab or architectural shingles into strips to minimize the number of exposed nails.īelow is how to install the last row of shingles on a standard shed roof. You could, but you would have tons of exposed nails, which is a recipe for leaks. Finishing the last row of your shingles isn’t as easy as throwing one last course of shingles on and calling it a day. Right now, let’s look at a regular, single sloping shed roof. Remember, a lean-to shed is just that – a lean-to! It leans against another structure, like your house, garage, or another shed. Later on, we’ll investigate the finer points of applying shingles to the top row of a lean-to type shed. Shed roofs come in all shapes and sizes, but we are looking specifically at two types: single slope and lean-to. How to Finish the Top Edge of a Shed Roof How to Finish the Lean To Roof Leading Edge.How to Finish the Top Edge of a Shed Roof.In addition, secure the asphalt shingles to the roof decking with tacks. Don’t forget that the shingles should overhang from the drip edge about a 1/4″. Repeat the process from the beginning, starting with the seventh course. Smart Tip: The first course should star with a 3 tab shingle, the second course with a 2 1/2 tab, the third course with a 2 tab, the forth course with a 1 1/2 tab, the fifth course with a 1 tab, the sixth course with a 1/2 tab. ![]() Always read the manufacturing instructions before starting the installation, as there are several aspects that differ. Place a starting course at the bottom of the roof, before installing the asphalt shingles. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under. Secure the tar paper to the plywood sheets with roofing staples. Therefore, install roofing felt over the roofing sheets, making sure the strips overlap at least 2″″. You could fit asphalt shingles to protect the shed, as it is a straight forward solution. How to build a lean to shed roof for a 8×10 shed Chalk line, tape measure, spirit level, carpentry pencil.120 sq ft of tar paper, 120 sq ft of asphalt shingles.P – 2 pieces of 1×4 lumber – 82 1/2″ long, 2 pieces – 83 1/4″ long, 4 pieces -107″ long TRIMS.O – 1 piece of T1-11 siding – 36″x75 3/4″ long, 2 pieces of 2×4 lumber – 68″ long, 2 pieces – 36″ long, 1 piece – 29″ long 2x DOOR.N – 2 pieces of 2×4 lumber – 72 1/4″ long, 1 piece – 79″ long JAMBS.M – 60 sq ft of tar paper, 60 sq ft of asphalt shingles ROOFING.K – 120 sq ft of tar paper, 120 sq ft of asphalt shingles ROOFING.J – 2 pieces of 2×6 lumber – 120″ long, 2 pieces of 1×6 lumber – 124 1/4″ long TRIMS.H – 9 pieces of 2×4 lumber – 120″ long RAFTER. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |